(CLEARANCE SALES) PROFFIEBOARD V2.2 – SOUND BOARD ONLY – 40 fonts preloaded

Description

Approved Official Board Makers 

Prior to purchase, please note that due to the nature of the board installation boards are PRETESTED and are non-Refundable due to user created protentional errors.  Boards aren’t sold with any defects as they are tested in 3 different processes at the factory created and onsite prior to shipping.  by purchasing you agree and understand this notification.

Color scheme: black with gold accent

* run has been approved and supported for custom darkwolf sabers 

* test rig for quality control has been purchased and shipped to our main factory overseas.

* Boards are sold and shipped out of the usa.

* We will be the sole distributor of this run during the run unless announced otherwise.

* ALL Required Chips Installed and Board Tested for Full Spec Functionality

*All updated to current OS 7.1.3

IMPORTANT : 

****Ensure not to use ANY Power source larger then 5v 1A. this includes IPHONE Bricks, Samsung, computer or laptop hubs, Gaming Devices or USB Hubs.  Failure to do so can Void your Warranty.

******INCORRECT VOLTAGE CAN CAUSE ANY BOARD TO OVERHEAT ENSURE TO USE PROPER CHARGING BRICK OR DATA LINE

Board will be preloaded ready to solder.

– pixel

board comes preloaded with additional 40 fonts 

“Support your font makers.”

Specs:

* Board is preinstalled and programmed ready for installation wiring comes with SD card

* Board is Black with Darkwolf Name on it 

*BATT+ – 2.6 to 4.5 volt input, drives everything except the LEDs

*Prior to shipping board is uploaded for testing connection as well loaded with most current OS listed 

• BATT- – negative pad for LEDs, needs to be at same level as GND when both are connected. Note that there are two of them, which can be useful when driving many powerful LEDs.
• GND – ground for electronics except LEDs. Note that the two GND pads are interchangeable and connected through the board.
• Button 1/2/3 – Hook up to closing buttons, or potentially touch buttons.
• Data 1 / ID – Normally used to measure the blade ID resistor, and if it’s a neopixel blade, feed out neopixel data.  For a fixed non-neopixel saber, it could be repurposed. Note that this pin has an internal 470 ohm resistor on it, so when hooked up to a neopixel blade, it does not need any resistors.
• Data 2-3 – additional neopixel data outputs, or free for other purposes.
• Data4/Dac – Neopixel data output, free, or audio DAC output
• LED 1-6 – Hooks up to negative side of LED (positive side of LED hooks up directly to battery.) These pads can handle up to 30 volts.
• SD Power – FET-controlled 3.3v. can be used to power down bluetooth and displays in low-power mode.
• SDA, SCL – these pins are used to communicate with the gyro and accelerometer chip.
• 5v – generated by the proffieboard, normally it’s only on when sound is playing.
• 3.3v – generated by the proffieboard.
• SWDIO, SWDCLK – can be hooked up to a ST-LINK device and lets you debug programs running on the proffieboard.

A note on reverse polarity protection This version of the proffieboard is the first to feature reverse polarity protection. Please note however, that the reverse polarity protection does not really cover the LEDs. The FETs have internal bypass diodes that lets power flow backwards through them. For regular LEDs, this is not a problem, as power can only flow one way through a LED. Neopixels might not be so lucky though, so it may still be possible to fry your pixels by hooking up the battery backwards. But the Proffieboard itself should be fine.

Resources : 

installation image is in the post gallery

 

primary site

https://fredrik.hubbe.net/lightsaber/v5/

open source page forum

https://www.facebook.com/groups/288564715213016/

tutorial beginners

https://www.youtube.com/watch?v=JMNg-pkQrA4

Listed fonts 

On standalone proffie

Pre-installed sound fonts 

• 1 – Krossguard
• 2 –  Final Steps (Yellow Rey)
• 3 –  Darksaber (White)
• 4 –  Ascension (green)
• 5 –  Crimson Menace (Maul) (Red)
• 6 –  Traveler(Malicos) (Red)
• 7 –  Young Solo(Ben) (Blue)
• 8 –  Empress Palatine (Fire unstable red)
• 9 –  Duke (Count Dooku) (Red)
• 10 – The Bold One (Obi-Wan) (Sky blue)
• 11 – Rogue Commander (Red)
• 12 – Darkness (Dark Rey)(Fire Blade)
• 13 – ESB Graflex (cyan)
• 14 – The Survivor (Fallen_Order) (Orange)
• 15 – Royalty (Leia) (Sky Blue)
• 16 – Darth Revan (Magneta)
• 17 – Starkiller (Sky Blue)
• 18 – Ashoka (White)
• 19 – Darkwolf (Blood Orange)
• 20 – TheMaw (Brian Conner)
• 21 – Ahsoka (Jordan_Clopton)
• 22 – Stasis (Purple Pulsing)
• 23 – Phoenix v2 (Golden Yellow)
• 24 – Deadlink (Magenta)
• 25 – The Butcher (Purple)
• 26 – Crispity (Cyan + Purple)
• 27 – Codex of Light (WHite Blade)
• 28 – Cyber Terror (Red) 
• 29 – Dark Ages (Yellow)
• 30 – Hatred (Red)
• 31 – Idyll (White)
• 32 – Serenity (Blue)
• 33 – The Champion (Purple)
• 34 – The Dark Lord Revisited (Red)
• 35 – The Learner (blue)
• 36 – The Second (red)
• 37 – The Teacher (green)
• 38 – Whispers of Power (orange)
• 39 – Arcane (Yellow)
• 40 – Tsukino (Cosmic ape)
• Rainbow – Spectrum (Rainbow)